Buy Tobacco Leaf Online | Whole Leaf Tobacco

Leverhead's Pipe Smoke-hole Dream Ream

Status
Not open for further replies.

deluxestogie

Administrator
Staff member
Joined
May 25, 2011
Messages
23,931
Points
113
Location
near Blacksburg, VA
Garden20130214_563_SmokeHoleReam_inPipe2_300.jpg
Garden20130214_564_SmokeHoleReam_inPipe1_300.jpg

Reaming a pipe's smoke-hole.

Most pipe smokers, myself among them, frequently run a chenille pipe cleaner through a pipe's smoke-hole to clean out the gunk. Water, alcohol or other "sweetening" solvent on the pipe cleaner does a fair job of removing most of the pyrogenic tars that would otherwise sour the pipe and eventually narrow the smoke-hole. I usually use a dry pipe cleaner.

At some point, though, the pipe tends to clog easily, and more aggressive methods are needed to remove the hardened deposits from the smoke-hole. If you've smoked a pipe for more than a few years, you've certainly experienced the frustration of trying to ream that tiny hole. For the past two decades, what I've used is a tiny steel rod with a triangular cross section. It's never worked particularly well.

Thanks to the metal working skill of leverhead, I now have the perfect smoke-hole reaming tool.
Garden20130214_555_SmokeHoleReam_entire_500.jpg

Leverhead's Pipe-hole Dream Ream.

The steel rod is 4-15/16" long, 3/32" diameter and springy like music wire, though it actually seems fairly rigid at this length.

Garden20130214_566_SmokeHoleReam_entireSide_500.jpg

Leverhead's Pipe-hole Dream Ream, handle side view.

The stiffness of the rod, and the 90º face of the tip (unlike the rounded tip of most pipe tool rods) allow me to remove even well hardened deposits from the smoke-hole. I've used it already on a dozen pipes, many dating to the 1970s. The shaft diameter seems perfect.

Garden20130214_558_SmokeHoleReam_tip_300.jpg

The tip is not chamfered, but is faced at 90º to the axis of the shaft.

One of my concerns was that it might gouge the wall of the smoke-hole in my meerschaum pipes. I noticed no problem with this. The briar shrugged it off as well.

One other concern was that the large handle was a bit of overkill. As it turns out, that handle is perfect for the amount of force that is sometimes required to push through the hardened crud.

Garden20130214_553_SmokeHoleReam_handle_300.jpg

The handle allows excellent control of the reaming force.

I just have to say that I love this thing. The one remaining question is why it took hundreds of years for someone to create such an important pipe tool.

Thank you, leverhead.

Bob
 

BigCasino

Well-Known Member
Joined
Jan 6, 2013
Messages
217
Points
0
Location
north of Pittsburgh
That is a nice tool leverhead made you

There is a tool called a senior pipe ream and certain ones have a draft hole ream in the handle
reamer-senior_small.jpg
 

deluxestogie

Administrator
Staff member
Joined
May 25, 2011
Messages
23,931
Points
113
Location
near Blacksburg, VA
Well, Harry, both I and my pipes qualify as "senior," so I must be eligible to purchase one of those aggressive looking gadgets.

I have occasionally used a small drill bit in the past, but it did not have an attached knurled handle, and was too short to use in a chuck. Leverhead's Dream Ream is also quite handy for pushing out thick gooey gunk, without the tedious cleaning of the tool required by a helical drill bit.

Bob
 

BarG

Founding Member
Joined
Jun 23, 2011
Messages
4,997
Points
113
Location
Texas, Brazos Vally
Way to go leverhead. It will be several years before I need one yet after aquiring my first pipe from knucks. You and Bob seem to be on the same page. You certainly are inventive and sorry I didn't contact and stop by today but I entered and exited houston on the other side of town.
 

darren1979

First Time Grower
Joined
May 5, 2012
Messages
431
Points
18
Location
Portsmouth, UK
Thats a good looking tool! Reminds me of a pen knife my dad had, a reamer but come to a point, an slicing knife and on the end a tapper for compressing the bowl.
 

leverhead

Well-Known Member
Joined
Jan 16, 2012
Messages
3,204
Points
83
Location
Grimes County Texas
Knucklehead, the only machining I did was to the knob. The rod is a press fit, that's just a matter of picking the right reamer. The rod was cut off scrap from another job, years ago. That's where the Yankee comes out, I can't bring myself to throw out a good piece of steel.
 
Status
Not open for further replies.
Top